{
    "type": "machine",
    "name": "Anycubic Kobra 2 0.4 nozzle",
    "inherits": "fdm_machine_common",
    "from": "system",
    "setting_id": "GM001",
    "instantiation": "true",
    "printer_model": "Anycubic Kobra 2",
    "default_print_profile": "0.20mm Standard @Anycubic Kobra2",
    "nozzle_diameter": [
        "0.4"
    ],
    "printable_area": [
        "0x0",
        "220x0",
        "220x220",
        "0x220"
    ],
    "printable_height": "250",
    "nozzle_type": "undefine",
    "auxiliary_fan": "0",
    "machine_max_acceleration_extruding": [
        "2500",
        "2500"
    ],
    "machine_max_acceleration_retracting": [
        "2500",
        "2500"
    ],
    "machine_max_acceleration_travel": [
        "3000",
        "1250"
    ],
    "machine_max_acceleration_x": [
        "2500",
        "2500"
    ],
    "machine_max_acceleration_y": [
        "2500",
        "2500"
    ],
    "machine_max_acceleration_z": [
        "800",
        "800"
    ],
    "machine_max_speed_e": [
        "80",
        "80"
    ],
    "machine_max_speed_x": [
        "300",
        "300"
    ],
    "machine_max_speed_y": [
        "250",
        "250"
    ],
    "machine_max_speed_z": [
        "8",
        "8"
    ],
    "machine_max_jerk_e": [
        "10",
        "10"
    ],
    "machine_max_jerk_x": [
        "15",
        "15"
    ],
    "machine_max_jerk_y": [
        "10",
        "10"
    ],
    "machine_max_jerk_z": [
        "2",
        "2"
    ],
    "max_layer_height": [
        "0.32"
    ],
    "min_layer_height": [
        "0.04"
    ],
    "printer_settings_id": "Anycubic",
    "retraction_minimum_travel": [
        "1"
    ],
    "retract_before_wipe": [
        "70%"
    ],
    "retraction_length": [
        "2"
    ],
    "retract_length_toolchange": [
        "1"
    ],
    "retraction_speed": [
        "80"
    ],
    "deretraction_speed": [
        "80"
    ],
    "single_extruder_multi_material": "1",
    "change_filament_gcode": "M600",
    "machine_pause_gcode": "M601",
    "default_filament_profile": [
        "Anycubic Generic PLA"
    ],
    "machine_start_gcode": "G90 ;Use absolute coordinates\nM83 ;Extruder relative mode\nM104 S[first_layer_temperature] ;Set extruder temp\nM140 S[first_layer_bed_temperature] ;Set bed temp\nM190 S[first_layer_bed_temperature] ;Wait for bed temp\nM109 S[first_layer_temperature] ;Wait for extruder temp\nG28 ;Move X/Y/Z to min endstops\nG1 Z0.28 ;Lift nozzle a bit\nG92 E0 ;Specify current extruder position as zero\nG1 Y3 F1800 ;Move Y to purge point\nG1 X60 E25 F500 ;Extrude 25mm of filament in a 5cm line\nG92 E0 ;Zero the extruded length again\nG1 E-2 F500 ;Retract a little\nG1 X70 F4000 ;Quickly wipe away from the filament line\nM117",
    "machine_end_gcode": "M104 S0 ;Extruder off\nM140 S0 ;Heatbed off\nM107 ;Fan off\nG91 ;Relative positioning\nG1 E-5 F3000 ;Retract filament\nG1 Z+0.3 F3000 ;Lift print head\nG28 X0 F3000 ;Home X axis\nM84 ;Disable stepper motors",
    "before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\n[layer_num] @ [layer_z]mm\nG92 E0",
    "layer_change_gcode": ";AFTER_LAYER_CHANGE\n[layer_num] @ [layer_z]mm",
    "scan_first_layer": "0"
}