{ "type": "machine", "name": "Artillery M1 Pro 0.4 nozzle", "inherits": "fdm_machine_common", "from": "system", "setting_id": "GM007", "instantiation": "true", "is_artillery": "1", "emit_machine_limits_to_gcode": "1", "layer_change_gcode": "G92 E0\n{if layer_num==2}\n\n;filter_fan\nM106 P3 S{during_print_exhaust_fan_speed[0]*255/100.0};\n\n;auxiliary_fan\nM106 P2 S{additional_cooling_fan_speed[0]*255/100.0}\n\n{endif}\n\n", "machine_end_gcode": ";===== G-CODE START =====================\n;===== machine: M1 PRO =========================\n;===== date: 20250729 =====================\n\n;===== Raise Z-Axis =====================\nM400 ; wait for buffer to clear\nG90\nG92 E0 ; zero the extruder\nG1 E-0.8 F1800 ; retract\n\n{if max_layer_z < printable_height}G1 Z{z_offset+min(max_layer_z+2, printable_height)} F300 ; Move print head up{endif} \nG90\nG1 X200 Y260 F21000\nG1 X200 Y275 F6000\nG1 X160 Y275 F6000\nG1 X137 Y275 F3000\nM400\nTIMELAPSE_TAKE_FRAME\n{if max_layer_z < 50}G1 Z50 F300 ; Move print head further up{endif}\n;===== Default Settings =====================\nM400\nM106 S255\nM141 S0\nM106 P1 S255\nM104 S160\nG4 P10000\nM109 S160\nM106 S0 ;turn off cool fan\nM141 S0 ;turn off PTC\nM106 P2 S0 ;turn off chamber fan\nM106 P1 S0 ;turn off PTC fan\nM106 P3 S0 ;turn off filter fan\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nSET_VELOCITY_LIMIT VELOCITY=500;\nSET_VELOCITY_LIMIT ACCEL=6000;\nSET_VELOCITY_LIMIT MINIMUM_CRUISE_RATIO=0.2;\nSET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY=5;\nG21; set units to millimeters\nM104 S0\nM140 S0\nM400\nM84 X Y Z E ; disable motors\nM400\n;===== G-CODE END =====================", "machine_max_acceleration_extruding": [ "20000", "1250" ], "machine_max_acceleration_retracting": [ "5000", "1250" ], "machine_max_acceleration_x": [ "20000", "1000" ], "machine_max_acceleration_y": [ "20000", "1000" ], "machine_max_jerk_e": [ "2.5", "2.5" ], "machine_max_jerk_x": [ "9", "10" ], "machine_max_jerk_y": [ "9", "10" ], "machine_max_jerk_z": [ "3", "0.4" ], "machine_max_speed_e": [ "50", "120" ], "machine_max_speed_x": [ "700", "200" ], "machine_max_speed_y": [ "700", "200" ], "machine_max_speed_z": [ "20", "12" ], "machine_start_gcode": ";===== START G-CODE =====================\n;===== machine: M1 PRO =========================\n;===== size: X260 Y260 Z260 =====================\n;===== date: 20250708 =====================\n;===== Filament Temperature Configuration =====================\n;Nozzle_Preheat_Temp:140\n;Bed_Preheat_Temp:[bed_temperature_initial_layer_single]\n{if (nozzle_temperature_initial_layer[0] >250)};Filament_Common_Extrusion_Temp:[nozzle_temperature_initial_layer]{else};Filament_Common_Extrusion_Temp:250{endif}\n;Nozzle_Init_Layer_Temp:[nozzle_temperature_initial_layer]\n;Filament_Softening_Temp:[nozzle_temperature_range_low]\n;Chamber_Temp:{chamber_temperature[0]}\n\n;===== Default Settings =====================\nM106 S0 ;turn off cool fan\nM141 S0 ;turn off PTC\nM106 P2 S0 ;turn off chamber fan\nM106 P1 S0 ;turn off PTC fan\nM106 P3 S0 ;turn off filter fan\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nSET_VELOCITY_LIMIT VELOCITY=500;\nSET_VELOCITY_LIMIT ACCEL=6000;\nSET_VELOCITY_LIMIT MINIMUM_CRUISE_RATIO=0.2;\nSET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY=5;\nG21; set units to millimeters\nG90\n\n;===== Preheat While Zeroing =====================\nM106 P1 S153\n\nM140 S[bed_temperature_initial_layer_single];\n\n{if filament_type[initial_no_support_extruder]==\"ABS\"}\nM106 P1 S255\nM106 P2 S60\nG4 P5000\nM191 S47;\nM141 S{chamber_temperature[0]};\n{endif}\n\n{if filament_type[initial_no_support_extruder]==\"PC\"}\nM106 P1 S255\nM106 P2 S60\nG4 P5000\nM191 S47;\nM141 S{chamber_temperature[0]};\n{endif}\n\n{if filament_type[initial_no_support_extruder]==\"ASA\"}\nM106 P1 S255\nM106 P2 S60\nG4 P5000\nM191 S47;\nM141 S{chamber_temperature[0]};\n{endif}\n\n{if filament_type[initial_no_support_extruder]==\"PA\"}\nM106 P1 S255\nM106 P2 S60\nG4 P5000\nM191 S47;\nM141 S{chamber_temperature[0]};\n{endif}\n\n{if filament_type[initial_no_support_extruder]==\"PA-CF\"}\nM106 P1 S255\nM106 P2 S60\nG4 P5000\nM191 S47;\nM141 S{chamber_temperature[0]};\n{endif}\n\nM106 P2 S0\nM106 S0;\nG4 P500\n\n;===== Wait heating =====================\nG28\nG1 X20 Y2 Z0 F18000\n\n;===== Set Print Temperature =====================\nM106 S120;\nG4 P500\nM104 S[first_layer_temperature];\n\n{if (bed_temperature_initial_layer_single >0)}\nM190 S[bed_temperature_initial_layer_single];\n{else}\nM140 S[bed_temperature_initial_layer_single];\n{endif}\n\nM109 S[first_layer_temperature];\nM106 S0;\nG4 P500\n\n;===== Wipe Nozzle Extrude Line =====================\nG1 X20 Y2 Z0 F18000\nM400\n\nG92 E0\nG0 E4;\nM400\n\nG92 E0\nG1 X240 Y2 Z0.2 F1800.0 E11.0;\n\nG92 E0\nG1 X240 Y10 Z0.2 F1800.0 E1;\n\nG92 E0\nG1 X239.5\nG0 E0.2\n\nG92 E0\nG0 Y2.5 E0.125\n\nG92 E0\nG1 X20 F1800.0 E11;\n\nM400\nG92 E0\nG1 Z0.6 F600\nM400\n\nG1 X{first_layer_print_min[0]} Y{first_layer_print_min[1]} F9000\nM400\n\n;===== END G-CODE =====================\n\n\n", "print_host": "192.168.3.29", "printable_area": [ "0x0", "260x0", "260x260", "0x260" ], "printer_settings_id": "Artillery M1 Pro 0.4 nozzle", "retraction_length": [ "0.8" ], "z_hop": [ "0.6" ], "printer_model": "Artillery M1 Pro", "nozzle_diameter": [ "0.4" ], "default_filament_profile": [ "Artillery PLA Basic" ], "adaptive_bed_mesh_margin": "0", "auxiliary_fan": "1", "bbl_use_printhost": "0", "bed_custom_model": "", "bed_custom_texture": "", "bed_exclude_area": [ "0x0" ], "bed_mesh_max": "99999,99999", "bed_mesh_min": "-99999,-99999", "bed_mesh_probe_distance": "50,50", "before_layer_change_gcode": "\n", "best_object_pos": "0.5,0.5", "change_extrusion_role_gcode": "", "change_filament_gcode": "G1 E-2 F2400\nG2 Z{z_after_toolchange + 0.4} I0.86 J0.86 P1 F10000\nT[next_extruder]", "cooling_tube_length": "0", "cooling_tube_retraction": "0", "default_print_profile": "0.20mm Standard @Artillery Genius", "deretraction_speed": [ "40" ], "disable_m73": "0", "enable_filament_ramming": "0", "extra_loading_move": "0", "extruder_clearance_height_to_lid": "140", "extruder_clearance_height_to_rod": "36", "extruder_clearance_radius": "65", "extruder_colour": [ "#018001" ], "extruder_offset": [ "0x0" ], "fan_kickstart": "0", "fan_speedup_overhangs": "1", "fan_speedup_time": "0", "gcode_flavor": "klipper", "head_wrap_detect_zone": [], "high_current_on_filament_swap": "0", "machine_load_filament_time": "0", "machine_max_acceleration_e": [ "5000", "5000" ], "machine_max_acceleration_travel": [ "1000", "1250" ], "machine_max_acceleration_z": [ "500", "200" ], "machine_min_extruding_rate": [ "0", "0" ], "machine_min_travel_rate": [ "0", "0" ], "machine_pause_gcode": "M600", "machine_unload_filament_time": "0", "manual_filament_change": "0", "max_layer_height": [ "0.32" ], "min_layer_height": [ "0.08" ], "nozzle_hrc": "0", "nozzle_type": "hardened_steel", "nozzle_volume": "0", "parking_pos_retraction": "0", "preferred_orientation": "0", "print_host_webui": "", "printable_height": "260", "printer_notes": "", "printer_structure": "undefine", "printer_technology": "FFF", "printer_variant": "0.4", "printhost_apikey": "", "printhost_authorization_type": "key", "printhost_cafile": "", "printhost_password": "", "printhost_port": "", "printhost_ssl_ignore_revoke": "0", "printhost_user": "", "printing_by_object_gcode": "", "purge_in_prime_tower": "0", "retract_before_wipe": [ "70%" ], "retract_length_toolchange": [ "0" ], "retract_lift_above": [ "0" ], "retract_lift_below": [ "0" ], "retract_lift_enforce": [ "All Surfaces" ], "retract_restart_extra": [ "0" ], "retract_restart_extra_toolchange": [ "0" ], "retract_when_changing_layer": [ "1" ], "retraction_minimum_travel": [ "1" ], "retraction_speed": [ "40" ], "scan_first_layer": "0", "silent_mode": "0", "single_extruder_multi_material": "1", "support_air_filtration": "1", "support_chamber_temp_control": "1", "support_multi_bed_types": "1", "template_custom_gcode": "", "thumbnails": [ "300x300" ], "thumbnails_format": "PNG", "time_cost": "0", "upward_compatible_machine": [], "use_firmware_retraction": "0", "use_relative_e_distances": "1", "wipe": [ "1" ], "wipe_distance": [ "2" ], "z_hop_types": [ "Slope Lift" ], "z_offset": "0", "time_lapse_gcode": "TIMELAPSE_TAKE_FRAME" }