{
    "type": "machine",
    "name": "Creality Ender-3 V3 SE 0.6 nozzle",
    "inherits": "fdm_creality_common",
    "from": "system",
    "setting_id": "GM001",
    "instantiation": "true",
    "printer_settings_id": "Creality",
    "printer_model": "Creality Ender-3 V3 SE",
    "printer_variant": "0.6",
    "gcode_flavor": "marlin2",
    "printer_structure": "i3",
    "default_print_profile": "0.20mm Standard @Creality Ender3V3SE 0.6",
    "extruder_clearance_height_to_rod": "47",
    "extruder_clearance_radius": "90",
    "machine_load_filament_time": "11",
    "nozzle_diameter": [
        "0.6"
    ],
    "printable_area": [
        "0x0",
        "220x0",
        "220x220",
        "0x220"
    ],
    "printable_height": "250",
    "nozzle_type": "brass",
    "auxiliary_fan": "0",
    "machine_max_acceleration_extruding": [
        "2500",
        "2500"
    ],
    "machine_max_acceleration_retracting": [
        "500",
        "500"
    ],
    "machine_max_acceleration_travel": [
        "2500",
        "2500"
    ],
    "machine_max_acceleration_x": [
        "2500",
        "2500"
    ],
    "machine_max_acceleration_y": [
        "2500",
        "2500"
    ],
    "machine_max_acceleration_z": [
        "500",
        "500"
    ],
    "machine_max_speed_e": [
        "40",
        "40"
    ],
    "machine_max_speed_x": [
        "250",
        "250"
    ],
    "machine_max_speed_y": [
        "250",
        "250"
    ],
    "machine_max_speed_z": [
        "5",
        "5"
    ],
    "machine_max_jerk_e": [
        "5",
        "5"
    ],
    "machine_max_jerk_x": [
        "10",
        "10"
    ],
    "machine_max_jerk_y": [
        "10",
        "10"
    ],
    "machine_max_jerk_z": [
        "0.4",
        "0.4"
    ],
    "max_layer_height": [
        "0.48"
    ],
    "min_layer_height": [
        "0.12"
    ],
    "retraction_minimum_travel": [
        "2"
    ],
    "retract_before_wipe": [
        "70%"
    ],
    "retraction_length": [
        "1.2"
    ],
    "retract_length_toolchange": [
        "1"
    ],
    "retraction_speed": [
        "40"
    ],
    "deretraction_speed": [
        "30"
    ],
    "z_hop_types": [
        "Spiral Lift"
    ],
    "single_extruder_multi_material": "1",
    "manual_filament_change": "1",
    "change_filament_gcode": "M600",
    "machine_pause_gcode": "M25",
    "default_filament_profile": [
        "Creality Generic PLA @Ender-3V3-all"
    ],
    "file_start_gcode": ";FLAVOR:Marlin\\n;TIME:{print_time_sec}\\n;Filament used:{used_filament_length}m\\n;Layer height:{layer_height}",
    "machine_start_gcode": "M220 S100 ;Reset Feedrate \nM221 S100 ;Reset Flowrate \n \nM104 S[nozzle_temperature_initial_layer] ;Set final nozzle temp \nM190 S[bed_temperature_initial_layer_single] ;Set and wait for bed temp to stabilize \nG28 ;Home \nG92 E0 ;Reset Extruder \nG1 Z2.0 F3000 ;Move Z Axis up \nG1 X-2.1 Y20 Z0.28 F5000.0 ;Move to start position \nM109 S[nozzle_temperature_initial_layer] ;Wait for nozzle temp to stabilize \nG1 X-2.1 Y145.0 Z0.28 F1500.0 E15 ;Draw the first line \nG1 X-2.4 Y145.0 Z0.28 F5000.0 ;Move to side a little \nG1 X-2.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line \nG92 E0  ;Reset Extruder \nG1 E-1.0000 F1800 ;Retract a bit \nG1 Z2.0 F3000 ;Move Z Axis up \nG1 E0.0000 F1800",
    "machine_end_gcode": "G91 ;Relative positionning \nG1 E-2 F2700 ;Retract a bit \nG1 E-2 Z0.2 F2400 ;Retract and raise Z \nG1 X5 Y5 F3000 ;Wipe out \nG1 Z10 ;Raise Z more \nG90 ;Absolute positionning \n \nG1 X0 Y220 ;Present print \nM106 S0 ;Turn-off fan \nM104 S0 ;Turn-off hotend \nM140 S0 ;Turn-off bed \n \nM84 X Y E ;Disable all steppers but Z",
    "scan_first_layer": "0",
    "disable_m73": "1",
    "thumbnails": []
}