{
    "type": "machine",
    "name": "Kingroon KP3S PRO V2 0.4 nozzle",
    "inherits": "fdm_klipper_common",
    "from": "system",
    "setting_id": "GM003",
    "instantiation": "true",
    "printer_model": "Kingroon KP3S PRO V2",
    "default_filament_profile": "Generic PLA @System",
    "default_print_profile": "0.20mm Standard @Kingroon KP3S PRO V2",
    "bed_exclude_area": [
        "0x0"
    ],
    "extruder_colour": [
        "#FCE94F"
    ],
    "layer_change_gcode": ";AFTER_LAYER_CHANGE\n;[layer_z]",
    "before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\n;[layer_z]\nG92 E0\n",
    "deretraction_speed": [
        "45"
    ],
    "machine_end_gcode": "{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+2, max_print_height)} F600 ; Move print head up{endif}\nG1 X5 Y200 F6000 ; present print\n{if max_layer_z < max_print_height-10}G1 Z{z_offset+min(max_layer_z+20, max_print_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < max_print_height*0.6}G1 Z{max_print_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors\nEND_PRINT",
    "machine_max_acceleration_e": [
        "10000",
        "5000"
    ],
    "machine_max_acceleration_extruding": [
        "10000",
        "9000"
    ],
    "machine_max_acceleration_retracting": [
        "10000",
        "9000"
    ],
    "machine_max_acceleration_x": [
        "10000",
        "9000"
    ],
    "machine_max_acceleration_y": [
        "10000",
        "9000"
    ],
    "machine_max_acceleration_z": [
        "10000",
        "100"
    ],
    "machine_max_jerk_e": [
        "20",
        "5"
    ],
    "machine_max_jerk_x": [
        "20",
        "7"
    ],
    "machine_max_jerk_y": [
        "20",
        "7"
    ],
    "machine_start_gcode": "START_PRINT EXTRUDER_TEMP=[first_layer_temperature] BED_TEMP=[first_layer_bed_temperature]\nCANCEL_POWEROFF\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nG92 E0",
    "max_layer_height": [
        "0.32"
    ],
    "retraction_length": [
        "0.8"
    ],
    "retraction_speed": [
        "45"
    ],
    "use_firmware_retraction": "1",
    "wipe": [
        "0"
    ],
    "z_hop": [
        "0"
    ],
    "printable_area": [
        "0x0",
        "205x0",
        "205x205",
        "0x205"
    ],
    "printable_height": "200",
    "nozzle_diameter": [
        "0.4"
    ]
}