{
    "type": "machine",
    "name": "Kingroon KP3S V1 0.4 nozzle",
    "inherits": "fdm_klipper_common",
    "from": "system",
    "setting_id": "GM003",
    "instantiation": "true",
    "printer_model": "Kingroon KP3S V1",
    "default_filament_profile": "Generic PLA @System",
    "default_print_profile": "0.20mm Standard @Kingroon KP3S V1",
    "thumbnails": [
        "100x100"
    ],
    "change_filament_gcode": "",
    "best_object_pos": "0.5,0.5",
    "change_extrusion_role_gcode": "",
    "cooling_tube_length": "0",
    "cooling_tube_retraction": "0",
    "deretraction_speed": [
        "30"
    ],
    "disable_m73": "0",
    "emit_machine_limits_to_gcode": "1",
    "enable_filament_ramming": "0",
    "head_wrap_detect_zone": [],
    "enable_long_retraction_when_cut": "0",
    "long_retractions_when_cut": [
        "0"
    ],
    "retract_before_wipe": [
        "0%"
    ],
    "retraction_distances_when_cut": [
        "18"
    ],
    "extra_loading_move": "0",
    "extruder_clearance_height_to_rod": "36",
    "extruder_clearance_radius": "65",
    "high_current_on_filament_swap": "0",
    "machine_unload_filament_time": "0",
    "min_layer_height": "0.08",
    "parking_pos_retraction": "0",
    "preferred_orientation": "0",
    "printing_by_object_gcode": "",
    "purge_in_prime_tower": "0",
    "retract_lift_above": [
        "0"
    ],
    "retract_lift_below": [
        "0"
    ],
    "retract_lift_enforce": [
        "All Surfaces"
    ],
    "bed_exclude_area": [
        "0x0"
    ],
    "extruder_colour": [
        "#FCE94F"
    ],
    "layer_change_gcode": ";AFTER_LAYER_CHANGE\n;[layer_z]",
    "before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\n;[layer_z]\nG92 E0\n",
    "machine_end_gcode": "G91; relative positioning\n G1 Z1.0 F3000 ; move z up little to prevent scratching of print\n G90; absolute positioning\n G1 X0 Y180 F1000 ; prepare for part removal\n M104 S0; turn off extruder\n M140 S0 ; turn off bed\n G1 X0 Y180 F1000 ; prepare for part removal\n M84 ; disable motors\n M106 S0 ; turn off fan",
    "machine_max_acceleration_e": [
        "5000",
        "5000"
    ],
    "machine_max_acceleration_extruding": [
        "10000",
        "20000"
    ],
    "machine_max_acceleration_retracting": [
        "5000",
        "5000"
    ],
    "machine_max_acceleration_travel": [
        "20000",
        "20000"
    ],
    "machine_max_acceleration_x": [
        "10000",
        "20000"
    ],
    "machine_max_acceleration_y": [
        "10000",
        "20000"
    ],
    "machine_max_acceleration_z": [
        "500",
        "200"
    ],
    "machine_max_jerk_e": [
        "2.5",
        "2.5"
    ],
    "machine_max_jerk_x": [
        "9",
        "9"
    ],
    "machine_max_jerk_y": [
        "9",
        "9"
    ],
    "machine_max_jerk_z": [
        "0.2",
        "0.4"
    ],
    "machine_max_speed_e": [
        "100",
        "25"
    ],
    "machine_max_speed_z": [
        "12",
        "12"
    ],
    "machine_pause_gcode": "PAUSE",
    "machine_start_gcode": "M104 S{first_layer_temperature[0]} ; set final nozzle temp\nM190 S[bed_temperature_initial_layer_single]\nM109 S[nozzle_temperature_initial_layer]\nM83\nG28 ; h1ome all axes\nG1 Z0.2                                   ; lift nozzle a bit \nG92 E0 \nG1 Y-3 F2400   \nG1 X50 F2400                                  ; zero the extruded length \nG1 X115  E40 F500                       ; Extrude 25mm of filament in a 5cm line. \nG92 E0                                     ; zero the extruded length again \nG1 E-0.2 F3000                                ; Retract a little \nG1 X180 F4000                              ; Quickly wipe away from the filament line\nM117",
    "manual_filament_change": "0",
    "nozzle_height": "4",
    "nozzle_type": "brass",
    "max_layer_height": [
        "0.32"
    ],
    "retraction_length": [
        "0.8"
    ],
    "retraction_speed": [
        "30"
    ],
    "support_air_filtration": "1",
    "support_chamber_temp_control": "1",
    "support_multi_bed_types": "0",
    "use_firmware_retraction": "0",
    "wipe": [
        "1"
    ],
    "z_hop": [
        "0"
    ],
    "z_offset": "0",
    "printable_area": [
        "0x0",
        "180x0",
        "180x180",
        "0x180"
    ],
    "printable_height": "180",
    "nozzle_diameter": [
        "0.4"
    ]
}